|
Actuation and Controls |
|
Pneumatic
* Electric * Accessories |
 |
Energy Pipe & Supply offers both
Pneumatic & Electric automation packages.
Based upon your service requirements,
our trained staff can design an automation package including the valve,
actuator, and accessories.
Components from manufactures such
as:
Apollo
Bettis
Conbraco
Deltorque
Moniteur Devices
PMV
Proximity
Rotork
Stonel
Westlock |
|
Apollo® CompactorqueTM Rack &
Pinion Actuator |
|
|
|

Conbraco Acutorque Stainless Steel Actuator |
 |
Investment
Cast Stainless Steel Body |
 |
Unique Drive Pinion: One piece
stainless steel alloy shaft, precision machined gear and teeth for
precise control. |
 |
Bearings: Replaceable top and bottom TFE
Pinion Bearings to ensure low friction, stability above 400°F, and
chemical resistance. |
 |
Travel Stops: Provides +/-4° travel
adjustment in outboard direction. |
 |
Accessory Mounting: Manufactured to
NAMUR to provide international standardized mounting. |
 |
Stainless Steel Pistons: Precision
cast pistons are guided through full face engagement with the opinion
and piston guide. |
 |
NAMUR Slotted Shaft: Standard to
provide a self-centering positive drive for positioners, a variety of
switches. |
 |
Actuator Mounting: Manufactured in
accordance with ISO 5211 to ensure mounting the actuator directly on
valves. |
 |
Pre-loaded Cartridges: Converts a
standard double acting actuator to a spring return unit by simply
removing the end caps and adding the spring cartridges. |
 |
NAMUR Solenoid Mounting:
International standard for direct mounting of solenoid valves.
|
|
|

Conbraco G-Series Scotch-Yoke Actuator |
 | Operating Ranges
G-Series double acting actuators produce guaranteed minimum torque
outputs from 10,000 lb-in. up to 6,000,000 lb-in. The spring return
units produce spring torques from 2,500 lb-in. to 3,000,000 lb-in.
|
 | Standard operating pressures:
Pneumatic — to 200 psig (14 BAR) |
 | NAMUR
The shaft driven accessory interface conforms to the NAMUR standard
and is identical on all G-Series actuators, allowing for
standardization of accessory mounting hardware and installation
practices |
 | Pneumatic and hydraulic scotch-yoke actuators
|
 | Automates ball, butterfly, plug valves and any
other 90° rotating mechanisms |
 | Salt Spray Testing per ASTM B117 criteria.
Construction features prevent water ingress, allowing G-Series
actuators to meet IP 66 and IP 67M specifications and severe high
pressure water deluge test |
 | Standard operating temperature is -20°F to
+200°F (-29°C to +93°C) |
 | Optional trims available:
0°F to +350°F (-18°C to +177°C)
-50°F to +180°F (-46°C to +82°C) |
 | Mechanical and hydraulic manual overrides are
available |
 | MSS and ISO Valve Mounting
The G-Series valve interface meets the dimensional requirements of MSS
SP-101 or ISO 5211 defined for each torque range
|
|
|

Apollo® AE Series Actuator |
 | Five Output Torques, One Housing -
200, 400, 600, 800 and 1,000 inch-pounds |
 | Long Service Life |
 | Newly developed anodized die cast aluminum housing
|
 | Fiberglass reinforced nylon cover with UV
stabilizers resists corrosion |
 | Nitrile gasket and seals cover all penetration
points in housing and cover |
 | Precision cut and heat treated alloy spur gears
|
 | Permanently lubricated enclosed gear train |
 | Two separate 1/2” NPT conduit entrances for easier
wiring and signal separation |
 | 12-position pre-wired terminal strip includes
standard connections for remote open/closed position indicators; lots
of room for wiring options |
 | Unrestricted mounting orientation |
 | Built-in thermal overload protection in all AC
motor
actuators |
 | Limit switches have an 11 amp rating at 115 VAC
|
 | High visibility valve position indicator standard
on all
models |
 | Actuators can be ordered with one, two or three
additional limit switches |
 | For low temperatures: actuators can be equipped
with a thermostatically controlled heater element |
 | Motor brake is necessary when mounting actuator to
a butterfly valve
|
|
|

Indicators * Limit Switches *
Solenoid Valves * Positioners *
Lockouts |
|
Automation packages are completed
with accessories supplied from ASCO, Stonel, Moniteur, Westlock,
Proximity, PMV, and VRC among others. |